Friday, February 24, 2017

3D Printing: HMT Rajat Caseback Remover - Printing

This week, I'm printing out the HMT Rajat watch caseback remover from last week on my Prusa i3 Rework 3D printer. Here is a quick photo gallery:





















These are the complete Slic3r settings I used:

; filament used = 2010.6mm (14.2cm3)

; avoid_crossing_perimeters = 0
; bed_size = 190,140
; bed_temperature = 30
; bridge_acceleration = 0
; bridge_fan_speed = 100
; bridge_flow_ratio = 1
; brim_width = 0
; complete_objects = 0
; cooling = 1
; default_acceleration = 0
; disable_fan_first_layers = 1
; duplicate_distance = 6
; end_gcode = M104 S0 ; turn off temperature for hotend\nM140 S0; turn off temperature for bed\nG28 X0  ; home X axis\nM84     ; disable motors\n
; external_perimeters_first = 0
; extruder_clearance_height = 40
; extruder_clearance_radius = 40
; extruder_offset = 0x0
; extrusion_axis = E
; extrusion_multiplier = 1
; fan_always_on = 1
; fan_below_layer_time = 60
; filament_diameter = 3
; first_layer_acceleration = 0
; first_layer_bed_temperature = 30
; first_layer_extrusion_width = 0
; first_layer_speed = 25%
; first_layer_temperature = 185
; g0 = 0
; gcode_arcs = 0
; gcode_comments = 0
; gcode_flavor = reprap
; infill_acceleration = 0
; infill_first = 0
; layer_gcode = 
; max_fan_speed = 100
; min_fan_speed = 35
; min_print_speed = 10
; min_skirt_length = 0
; notes = 
; nozzle_diameter = 0.4
; only_retract_when_crossing_perimeters = 1
; ooze_prevention = 0
; output_filename_format = [input_filename_base].gcode
; perimeter_acceleration = 0
; post_process = 
; print_center = 95,70
; resolution = 0
; retract_before_travel = 1
; retract_layer_change = 1
; retract_length = 2.5
; retract_length_toolchange = 10
; retract_lift = 0.5
; retract_restart_extra = 0
; retract_restart_extra_toolchange = 0
; retract_speed = 20
; skirt_distance = 6
; skirt_height = 1
; skirts = 5
; slowdown_below_layer_time = 30
; spiral_vase = 0
; standby_temperature_delta = -5
; start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle
; temperature = 185
; threads = 2
; toolchange_gcode = 
; travel_speed = 50
; use_firmware_retraction = 0
; use_relative_e_distances = 0
; vibration_limit = 0
; wipe = 1
; z_offset = 0
; dont_support_bridges = 0
; extrusion_width = 0
; first_layer_height = 0.12
; infill_only_where_needed = 0
; interface_shells = 0
; layer_height = 0.2
; raft_layers = 0
; seam_position = random
; support_material = 0
; support_material_angle = 45
; support_material_enforce_layers = 0
; support_material_extruder = 1
; support_material_extrusion_width = 0
; support_material_interface_extruder = 1
; support_material_interface_layers = 3
; support_material_interface_spacing = 0
; support_material_interface_speed = 100%
; support_material_pattern = pillars
; support_material_spacing = 1.5
; support_material_speed = 25
; support_material_threshold = 0
; bottom_solid_layers = 3
; bridge_speed = 60
; external_perimeter_speed = 60%
; extra_perimeters = 1
; fill_angle = 45
; fill_density = 85%
; fill_pattern = honeycomb
; gap_fill_speed = 10
; infill_every_layers = 1
; infill_extruder = 1
; infill_extrusion_width = 0
; infill_speed = 25
; overhangs = 1
; perimeter_extruder = 1
; perimeter_extrusion_width = 0
; perimeter_speed = 25
; perimeters = 3
; small_perimeter_speed = 10
; solid_fill_pattern = rectilinear
; solid_infill_below_area = 70
; solid_infill_every_layers = 0
; solid_infill_extrusion_width = 0
; solid_infill_speed = 100%
; thin_walls = 1
; top_infill_extrusion_width = 0
; top_solid_infill_speed = 20
; top_solid_layers = 3